P0730 Code Dodge Charger

Following codes related to transmission. By automatically selecting different speeds or gear ratios to deliver power to the wheels an automatic transmissions goal is to match the optimal torque and power characteristics of the engine to the desired speed and rate of acceleration of the driver.

Help Blue Tops And Limp Mode Archive Lx Forums Dodge Charger Challenger Magnum Hellcat Srt Chrysler 300 Forum

The tech didnt know much about it ive read that its a pretty generic code but their computer suggested to replace The automatic transmission connector and transmission cooler.

P0730 code dodge charger. The P0730 code identifies a problem within an automatic transmission. Transmission Control System Malfunction is the definition of OBD-II Trouble Code P0730. Torque converter slip ratio A x CB.

The transmission control module is programmed to immediately place the transmission into neutral if P0730 or P1731 codes are set. Fortunately this is a code that the retail auto parts stores dont immediately try selling parts to the potential customer. Also I feel the shifts sometimes go very high on RPMs before it changes without slamming on the gas.

The auto repairs diagnosis time and labor rates vary by location vehicles make and model and even your engine type. I was in auto mode and just pulled out of a parking lot when I heard the chime and saw the service engine light. These codes indicate that the transmission experienced an unknown or incorrect gear ratio.

Same scenario as above. Click the register link above to proceed. Low or dirty transmission fluid Worn pump or clogged fluid filter Torque converter clutch solenoid or internal blockage Mechanical failure inside transmission Internal blockage inside transmission main control Faulty shift solenoids or.

10 The cost to diagnose the P0733 DODGE code is 10 hour of labor. Many times this code indicates that the transmission may need to be replaced rebuilt or overhauled which can vary between 2500 and 5000. P0730 DODGE Description.

It seemed very sluggish Limp Mode. P0730 is the OBD-II generic code for an incorrect gear ratio detected in an automatic transmission. Since the P0700 doesnt indicate a problem it indicates that there is a problem here are some common problems that will cause the code to be thrown as well as some of the more common symptoms that something is wrong with the transmission.

Noticed it was not responding correctly. 21 - 38 of 38 Posts. P0730 Just happened to me Friday night.

Causes of this DTC may include. RT Engine Code Already - P0730 Gear Ratio Incorrect. This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module TCM as follows.

2006 dodge charger. You may have to register before you can post. It was P0730 and it was in there twice.

P0700 HI I HAVE A 2006 DODGE CHARGER 35 ENGINE 2B3KA43G86H136761 WITH THE FOLLOWING CODES RELATED TO TRANSMISSION. Here is what it says about P0730. What Does P0730 Mean.

If this is your first visit be sure to check out the FAQ by clicking the link above. Went to AutoZone yesterday and had them pull up the code. Charger Discussion 2nd Gen - 2011 to 2014 Charger NEW CODE.

It read P0730 - Incorrect gear ratio. The check engine error code is P0730. Ive been driving for about 17 years of my life nowand have had 4 Dodge vehicles.

Placing the transmission in neutral prevents potential catastrophic failure. What is the cost to diagnose the P0733 DODGE code Labor. Bad transmission control module.

Output shaft revolution signal from speed sensor revolution sensor B. By the way yesterday in the evening the check engine code. Jump to Latest Follow Hey everyone.

Engine speed signal from Engine Control Module ECM. Loking for the meaning of code p0730 in a dodge charger - Dodge Charger question. What the P0730 code means.

Well it does not feel like it slips bad but maybe a very slight and quick slip. Enter your ride HERE to be a part of this months Ride of the Month Challenge. P0730 states incorrect gear ratio.

The Transmission Control Module TCM constantly calculates the transmission ratio based on the input speed sensor 1 and 2 N2-N3 signals and the calculated output shaft speed. The ABS are correct. The P0730 code is often associated with the P0729 P0731 P0732 P0733 P0734 P0735 and P0736 trouble codes.

Code P0730 Gear Ratio Incorrect.

Error Code P0730 Incorrect Gear Ratio Auto Service Costs